Products

FRP Pultruded Grating

Pultruded Gratings

FRP Pultruded Gratings are famous for high strength, corrosion resistance, long life and safety in the most difficult environment. These also adhere to the highest international standards. Ventura Fiber Tech design ensures that reliable services are possible for several years as they are assembled from interlocking pultruded profiles thus outperforming the traditional materials they replace.

Being lightweight, easy to put together and install, good performance and cost effectiveness makes it a better choice than steel in several major industries.

An entire collection of gratings is offered to satisfy wide-ranging industrial needs and high load requirements for safety at work.

Bearing Bars & Cross-rod Assemblies

Unlike molded grating which has equal strength in both directions, FRP Pultruded grating is stronger in the longitudinal direction as it is fabricated from bearing bars & interlocking rod and groove bar assemblies. For that reason FRP Pultruded grating sizes are specified by width (the cross-rod dimension) x length or span (the bearing bar dimension).

The bearing bars used for FRP Industrial grating are pultruded I bars and T Sections and these bars are 25mm (1 inch) and 38mm (1.5 inches) deep. For the 25mm (1 inch) deep grating the cross-rod assembly is used horizontally, whilst for 38mm (1.5 inches) and 50mm (2 inches) deep products cross rods are used vertically.

Bearing Bars & Cross-rod Assemblies
Bearing Bars & Cross-rod Assemblies
Bearing Bars & Cross-rod Assemblies
Bearing Bars & Cross-rod Assemblies
Bearing Bars & Cross-rod Assemblies
H-Height
(mm)
W-Top Width
(mm)
C-Spacing
(mm)
Open Area
(%)
I-1040 25 15 25 40
I-1050 25 15 30 50
I-1060 25 15 38 60
I-1540 38 15 25 40
I-1550 38 15 30 50
I-1560 38 15 38 60
T-1033 25 25 38 33
T-1050 25 25 50.8 50
T-1517 38 25 30.5 17
T-1533 38 25 38 33
T-1550 38 25 50.8 50
HD-1540 38 15 25 40
HD-1550 38 15 30 50
HD-1560 38 15 38 60
I Series
I Series
T Series
T Series
HD Series
HD Series
I Bar Assemblies

The I bar assemblies are offered in standard size with 40%, 50% and 60% open areas whereas the T bar assemblies have 17%, 33% & 50% open areas as standard. Nomenclature use to describe each industrial grating style refers to its bearing bar style (I or T), its open area and its metric depth.

For example...
I 1560 = I bearing bar: 60% open area: 38mm deep
T 1033 = T bearing bar: 33% open area: 25mm deep

Allowable Spans for Vehicular Loads

Wheel Load (kg)
1/2 Axle Load + 30% Impact
Load Distribution
(in mm)
Allowable span in mm
HD 1540 HD 1550 HD 1560
AASHTO Standard Truck4 / 14500 kg Axle Load
Dual Wheels (*formerly AASHTO H-20)
9425 kg 500 425 350 300
Automobile Traffic / 2200 kg Vehicle
700 kg Load / 55% Drive Axle Load
1000 kg 200 700 675 650
5 Ton Capacity Forklift / 6500 kg Vehicle
11500 kg Total Load / 85% Drive Axle Load
6350 kg 275 375 350 300
3 Ton Capacity Forklift / 4500 kg Vehicle
7500 kg Total Load / 85% Drive Axle Load
4150 kg 175 400 350 300
1 Ton Capacity Forklift / 2000 kg Vehicle
3000 kg Total Load / 85% Drive Axle Load
1650 kg 100 500 500 475

Fittings

Accessories:

Applicable for our gratings we have special support angles which are concreted into the basement directly.

Fixing Sets

Easy to assemble without any special tools. A pultruded Fiberglass angle can be used as a frame for all Fiberglass gratings.

Fittings
Fittings

Stainless steel fixing sets can be used for all standard Fiberglass gratings and support constructions. To prevent Fiberglass gratings perfectly against lifting and sliding away each panel should be fixed on at least four points.

M-Clip for Molded Grating

M-Clip for Molded Grating
M-Clip for Molded Grating

C-Clamp for Molded Grating

M-Clip for Molded Grating
M-Clip for Molded Grating

M-Clip Pultruded Grating

M-Clip for Molded Grating
M-Clip for Molded Grating
M-Clip for Molded Grating
M-Clip for Molded Grating

Fiberglass Step Treads

Fiberglass Step Treads

Easy to assemble and providing high safety. Fiberglass Step Treads fulfil high safety standards. They are produced in the same way as the Fiberglass Profile Gratings and the Fiberglass Molded Gratings with additionally reinforced and highlighted edges.

Color Selection

Color Selection

To complement any project design, Ventura Fiber Tech FRP Gratings are made available in variety of colors. Standard colors available for FRP Grating: Dark Grey, Yellow and Green. Custom colors are made available upon request.